- Available Formats
- Options
- Availability
- Priced From ( in USD )
- ?
- Immediate download
- $54.00
- Printed Edition
-
- Ships in 1-2 business days
- $54.00
- Printed Edition + PDF
-
- Immediate download
- $73.00
Customers Who Bought This Also Bought
ASTM Standards ASTM D638-03 pdf download. ASTM D638-03,Standard Test Method for Tensile Properties of Plastics. The standard is shared by an American netizen. This document can be downloaded here for free. I hope everyone has a heart of gratitude, and I also hope. Most of people like. ASTM C33/C33M-18,Standard Specification for Concrete Aggregates.This document is Shared by Grace from USA.ASTM C33 / C33M-18 PDF is available for free download. Key words:aggregates,coarse aggregate,concrete aggregates,fine aggregate. ASTM C33/C33M-18 is for use by a contractor, concrete supplier.
- FRPI Laminate Certification Manual, 2017 Edition
Priced From $285.00 - ASTM D1243-15
Priced From $42.00 - ASTM D2126-15
Priced From $42.00 - ASTM D1435-13
Priced From $50.00 Varma kalai books in tamil pdf free.
ASTM Standard D7234-12 for Pull Off Adhesion Strength of Coatings b. ASTM Standard G62-14 for Holiday Detection in Pipeline Coat ings III. Third Part Test Results Against ASTM and Other Standards a. ASTM D638 - Tensile Properties b. ASTM D695 - Compressive Strength c. ASTM D790 - Flexural Modulus d. ASTM D2240 - Hardness e.
About This Item
Full Description
1.1 This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
1.2 This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining.
1.3 This test method includes the option of determining Poisson's ratio at room temperature.
Note 1:This standard and ISO 527-1 address the same subject matter, but differ in technical content.
Note 2:This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed.
Note 3:This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651.
Note 4:For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106-psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M.
1.4 Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design.
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
![Astm D638 Pdf Free Download Astm D638 Pdf Free Download](https://www.pdffiller.com/preview/399/91/399091767.png)
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Document History
Browse related products from ASTM International
- ASTM International >By Sections and Volumes >Section 8 - Plastics >Volume 08.01 - Plastics (I): D 256 - D 2343
- ASTM International >By ICS Code >83: Rubber And Plastics Industries >83.080: Plastics >83.080.01: Plastics In General
⏱Adding Item to Cart..
Standard Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications1
This standard is issued under the fixed designation A 578/A578M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
Astm D638 Pdf Free Download
click below to downlaod A 578 A578M – 96 pdf free